Condividi:        

messaggio di HDD health: che significa?

Se il modem non funziona, hai problemi con la scheda video o non sai che processore scegliere entra qui!!

Moderatori: m.paolo, Caffey

messaggio di HDD health: che significa?

Postdi view17 » 21/12/05 19:52

x gli ignoranti che significa il seguente messaggio (in parole povere)?
"UltraDMA CRC Error Count attribute is very low! Check the IDE cable, PCI frequency and system drivers"
Mi devo preoccupare?
Grazie!
Ciao, Ivan
view17
Utente Junior
 
Post: 18
Iscritto il: 09/05/05 17:09

Sponsor
 

forse queste informazioni possono essere un po d'aiuto

Postdi view17 » 21/12/05 20:14

NOP command Supported
DOWNLOAD MICROCODE command Supported
READ DMA QUEUED and WRITE DMA QUEUED commands Not supported
CFA feature set Not supported
Advanced Power Management feature set Supported, Disabled
Removable Media Status feature set Not supported
Power-Up In Standby feature set Not supported
SET MAX security extension Supported, Disabled
Automatic Acoustic Management feature set Supported, Enabled
48-bit Address feature set Supported
Device Configuration Overlay feature set Supported
FLUSH CACHE command Supported
FLUSH CACHE EXT command Supported
SMART error logging Supported
SMART self-test Supported
Media serial number field words Not supported
Media Card Pass Through Command feature set Not supported
Streaming feature set Supported, Not executed
General Purpose Logging feature set Supported
WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT commands Supported
WRITE DMA QUEUED FUA EXT command Not supported
World wide name Not supported
URG bit for READ STREAM DMA and READ STREAM PIO commands Supported
URG bit for WRITE STREAM DMA and WRITE STREAM PIO commands Supported
Time-limited Read/write feature set Not supported
Read Continuoud and Write Continuous in the Time-limited Read/write feature set Not supported
Ultra DMA mode selected Mode 5
Ultra DMA mode supported Mode 6 and below
The time required for the SECURITY ERASE UNIT command to complete Value not specified
Time required for Enhanced security erase unit completion Value not specified
Advanced power management level value 0
Master Password Revision Code Not supported
Device vendor’s recommended acoustic management level 254
The current automatic acoustic management level 192
Stream Minimum Request Size 8
Streaming Transfer Time - DMA 0
Streaming Access Latency – DMA and PIO 41535
Removable Media Status Notification feature set Not supported
Enhanced security erase unit feature Not supported
The security count is expired and SECURITY UNLOCK and SECURITY ERASE UNIT are command aborted until a power-on reset or hardware reset.
CFA Power Mode Mode 1
Maximum average RMS current 1840 Milliamperes

Start/Stop Count (Power on count) 126 times
Reallocated Sectors Count 0 sectors
Power-On Hours 41559 minuties (hours)
Device Power Cycle Count 132 times
Temperature 29 °C
Reallocation Event Count 0 events
Current Pending Sector Count (Unstable sectors) 0 sectors
Uncorrectable Sector Count 0 sectors
UltraDMA CRC Error Count (total) 6272 errors
Write Error Rate (Multi Zone Error Rate) 0
view17
Utente Junior
 
Post: 18
Iscritto il: 09/05/05 17:09

Postdi luna11 » 22/12/05 00:18

Forse hai un HD ATA 133 collegato con un vecchio cavo ATA 33 o 66 .
Se hai una scheda madre con chipset Via dovresti installare i drivers 4in1.
luna11
Utente Senior
 
Post: 3634
Iscritto il: 10/08/01 01:00


Torna a Assistenza Hardware


Topic correlati a "messaggio di HDD health: che significa?":


Chi c’è in linea

Visitano il forum: Nessuno e 15 ospiti

cron